LED Strip Lights for Motor

These are amazing. They are super bright and Come with 3M tape on them. The reviews that say they don’t stay or fall off is due to not prepping the surface correctly. So here is some tips. Make sure to install in 70+ degree weather. Make sure the surface is entirely clean. Then use alcohol preps to clean it again until nothing shows on the alcohol prep pad. Then I highly recommend to use 3M 4298 Adhesion Promoter. Wait till it dries and then stick the lights on surface. Remember you will only have one shot at this. Trust me. Doing what I said above, it will NoT ever fall off. If ya find this review helpful please click below

I'm using these lights as auxiliary daytime running lights for my car. No, they are not as bright as the LED daytime running lights that come as standard equipment from the factory on many cars, but they are still quite bright for these types of LED strips. Perhaps ones that I've seen called "Max LED's" are a little brighter, but the those that I've seen do not have as many LED's per foot as these lights. I would describe the shade of white as a "cool white", but it is not quite as bluish as other cool white LED's that I've seen.I did put some transparent vinyl wrap over these strips, because, as with all of these types of LED strips that I have experience with, the clear flexible plastic that makes up the actual strip is soft and would likely get marked up with debris when mounted on the front of the car (this has happened with other flexible LED strips I have mounted on the front of a car). And I put some strip caulk at the end where the wires are attached to help enhance water resistance. I don't know if that was necessary or not, but the appearance of the shrink-wrapping where the wires are attached makes it look like water could get to the actual connections, but there would be no way for me to know for sure without removing the shrink-wrapping, which I did not want to do.I've only had these LED strips installed for about a week, so far, so only time will tell how they hold up and how well my modifications help protect them. But so far, I am very satisfied with this purchase.

I've purchased three different sets through the years and this one wins the cake. Wires are more substantial than the others, easier to strip (though DELICATELY) and actually have a POS+ / NEG- layout, but they don't mark them as such. They come with a 3M sticky strip already -- what a concept, right? Going to put them on my car, they need sticky stuff. These are the only ones I purchased that did this. Thank you Geeon!

I had high hopes for these and the looked like they were built better with 3M backing. I bought them with another set of LED lights to compare the different color of blue but all four in my package didn't even light up. I am experienced in installing these and the other set I had from a competitor lite up just find.

I installed these strip lights on my boat (yellow) under both dashes, along the the inside side rails, (white) engine, battery and storage compartments. Yellow keeps the bugs away and adds a beautiful glow to the floor area and white brightens the other areas when yo need to open them.I gave installation 4 stars because the Ad says you can run them together with the small double sided pins. If you do the voltage and ground pins are on opposite side of the strip joint and one side won't light. I had to twist one strip to align the pins properly so both lighted together.

All working prior to install on motorcycle trailer. 3 were inside trailer as dome lights, and i retrofitted a brake light with one. These are no different than many advertisements as waterproof, they don’t last. Were not working after one road trip, so I'm not sure if vibration does them in, or if it’s rain. We did drive through rain for a few hours. The retrofitted brake like bugs me the worst because I don’t know if it can be stripped redone again.

idgaf what the comments state here, these are not "easy" to install lol you gotta get in there and connect them somewhere in the car doors or whatever so if youre like me and you dont know squat on working on cars i suggest you get other ones that easily install to the car's cigarette lighter fuse (i have these). I got this as a gift thinking they were the same but nope. If anyone would kindly e-mail me a video on how the hell i install these I would greatly appreciate it cause I didnt even get installment instructions just lights in a bag.

I added these to the underside of the engine hood with a switch so that when the hood pops open, the light turns on. The lights are so bright that I can work throughout the night without additional lamps unless I need to get into some tight areas of the engine to work. Given the low battery use, I usually open the hood and leave these lights on at night so we have some better lighting around camp.