ATOPLEE 3 Phase Sequence Presence Rotation Tester Indicator Detector Meter with LED and Buzzer 60V~600V (3 Phase AC)

ATOPLEE 3 Phase Sequence Presence Rotation Tester Indicator Detector Meter with LED and Buzzer 60V~600V (3 Phase AC)

Q: Will this work on the output of a VFD?

Matthew, a vfd is a Variable Frequency Drive. they are used for phase shifting and/or voltage shifting. my father uses one to convert his 220 single phase to 480 3 phase for his mill in his home garage.

Q: Misplaced instruction. what color lead goes on line 1, line 2 and line 3? thanks

It actually doesn't matter as long as the phase sequence is right. Convention identifies each of the 3 leads as L1, L2, and L3. Your equipment will have terminals labeled as L1, L2, and L3. You would assume L1 goes to L1, L2 to L2 and L3 to L3. This is correct. However, you can also connect L1 to L2, L2 to L3 and L3 to L1. Surprise, you can connect L1 to L3, L2 to L1 and L3 to L2. Each of the 3 variations gives the same result and is correct. What does matter is the sequence. Each line will cycle to peak voltage in rotation. Thats why this is a Phase Sequence Rotation Meter. First L1 goes high, then L2, then L3. If you start with L2, then L3 and L1, each goes high in Rotation. Typically, equipment (a motor perhaps) expects to see "Clockwise" Rotation, sometimes called "Right Hand" Rotation. Should you wish to reverse rotation (for a motor) swap any 2 leads and you get "Counter Clockwise" Rotation, sometimes called "Left Hand" Rotation. Sometimes, one of the leads will register a slightly higher voltage to common/ground than the other two leads. This "Hot Leg" assists with starting a motor. Usually you need not pay any attention to this. Your equipment manual will tellyou if you do. Convention will call for the Hot Leg to be L1. So, hook up your tester, without regard to lead color. If It says "CW" rotation you're good. For convenience, call the Yellow lead L1, Green Lead L2 and Red Lead L3. Wire the associated power leads to the terminals designated L1, L2 and L3 on your equipment. You're good to go.

Q: I was just wondering why it will take so long to deliver. My friend purchased the same exact one from Amazon and it came in about 2 days

Supply chain delays, like everything else.

Q: i see the max voltage is listed for 600v will it survive 690 +/- 4% are the leads 1kv rated? i understand that it wont last as long on 690

I never used it on anything more than 480v. Couldn’t tell you if it would survive 690. As far as the leads being 1kv, it doesn’t say. Only states 600v rated.

4.5/5

Product ID: 390418809

Secure Transaction

Details

Brand
ATOPLEE
Power source
Battery
Style
Compact
Colour
['Orange']
Item weight
0.33 Pounds

⚡2000 V/min voltage limit

📏1m test leads for flexible reach

🔊LED & buzzer for clear alerts

Frequently Bought Together

ATOPLEE 3 Phase Sequence Presence Rotation Tester Indicator Detector Meter with LED and Buzzer 60V~600V (3 Phase AC)

Klein Tools ET600 Multimeter, Megohmmeter Insulation Tester, 4000 Ohms Resistance, 125V/250V/500V/1000V, Auto-Ranging TRMS Multimeter

Phase Rotation Meter Non-contact 3 Phase Rotation Meter AC 70~600V Phase Sequence Rotation Tester High Magnetic Induction Rotation Meter Auto Power Off Phase Meter with LED, 20-inch Clamp Lead,Handbag

Description

⚡ Stay ahead of the current—test with confidence and style!

COMPACT PORTABLE - Sleek 85x64x23mm design in vibrant orange—stand out on-site with ease.
OPTIMIZED USAGE TIME - Up to 60 minutes continuous use at 60V AC, perfect for extended diagnostics.
USER FRIENDLY ALERTS - Integrated LED and buzzer indicators ensure you never miss a phase sequence.
WIDE FREQUENCY RANGE - Operates seamlessly between 20 Hz and 400 Hz to cover diverse industrial needs.
PRECISION VOLTAGE HANDLING - Supports up to 2000 V/min with 4000 V impulse protection for ultimate safety.

The ATOPLEE 3 Phase Sequence Rotation Tester is a compact, battery-powered device designed for professionals needing reliable phase detection from 60V to 600V AC. Featuring a robust 2000 V/min voltage limit, wide 20-400 Hz frequency range, and intuitive LED plus buzzer alerts, it ensures precise and safe diagnostics. Its 1-meter test leads and lightweight design make it an essential tool for on-the-go electrical testing.

Specifications

Manufacturer	ATOPLEE
Part number	12040027001
Item Weight	150 g
Package Dimensions	20.2 x 13 x 5.9 cm; 149.69 g
Item model number	12040027001
Size	Instrument size: 85x64x23mm
Color	['Orange']
Style	Compact
Material	plastic
Power source type	Battery Powered
Item Package Quantity	1
Batteries Included?	No
Batteries Required?	No

Have a Question? See What Others Asked

Will this work on the output of a VFD?

Misplaced instruction. what color lead goes on line 1, line 2 and line 3? thanks

I was just wondering why it will take so long to deliver. My friend purchased the same exact one from Amazon and it came in about 2 days

i see the max voltage is listed for 600v will it survive 690 +/- 4% are the leads 1kv rated? i understand that it wont last as long on 690

Common Questions

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Ravi S.

I loved the variety of products available. Will definitely shop again.

2 months ago

Ali H.

Fast shipping and excellent packaging. The Leatherman tool feels very premium and sturdy.

1 day ago

View all Trustpilot reviews

Shop Global, Save with Desertcart

Value for Money

Competitive prices on a vast range of products

Shop Globally

Serving over 300 million shoppers across more than 200 countries

Enhanced Protection

Trusted payment options loved by worldwide shoppers

Customer Assurance

Trusted payment options loved by worldwide shoppers.

Desertcart App

Shop on the go, anytime, anywhere.

$743

Duties & taxes incl.

Solomon Islandsstore

Free Shipping

with PRO Membership

Free Returns

30 daysfor PRO membership users

15 dayswithout membership