HUIQIAODSH11 H8 880 881 High Temperature Ceramic Wire Harness Socket Female Adapter for Headlight Fog Light 2 pcs

As stated, replaced the faulty one Kia pigtails with these and have had great performance so far. Buyer beware the plastic is very fragile on these and is prone to breaking.

This works perfectly for my 2005 Volvo XC70. My XC70 had 3 wires going into the socket, two wires into one side and one in the other. I was a little concerned that this only had two wires, but I took the wire on this and the two wires on my cut wires from the old socket and put them all in a wire nut, and then took the single wire from the other side and connected it to the single wire from the old socket....worked perfectly!

My headlight was burnt out. Replaced the headlight bulb and it worked for a couple of days and then was off again - ugh. Took it back apart thinking that I would have to find the receipt and return the headlight bulb, but the bulb still looked good. Sure enough, the connector was melted some and did not allow a strong connection. Bought these and spliced them in, and it works great. Now I am thinking that the original headlight issue might have been the melted connector and NOT the bulb. Now I am good to go for a long while.

Went to splice in the new connector. Found the wire colors to be different between the new & old connectors. Used the fitting slot on the old connector, orientated the new connector to the old, to get the same wire orientation. Then cut, stripped, & spliced in one wire at a time. After connecting and putting in the reflector. The bulb needs a small turn downwards to seat. There I found the lower one side of the connector unlock tab runs into part of the lamp housing assembly. Will use a dremel to cut off that section on the unlock tab. Had no ceramic breakage problems after several attaching and unhooking of connector and bulb.

These connectors SEEM great. They are brittle and VERY fragile. I tried to use them to replace a melted Pontiac G6 low beam connector. Cutting and connecting the wires is easy. Almost anybody can do that so nothing to review there.When I went to plug in a new bulb, I was very cautious as I read the previous reviews. I looked and the pins lined up well. I did not even get the bulb 1/8 of the way inserted and I heard cracking. I pulled the bulb out and the inside middle of the ceramic broke and fell away. It was mostly intact. I again checked the pins and plastic divider in the bulb and it had no obstructions. I started inserting the bulb again as it was just a small piece the broke and fell away and again I heard cracking. Again I pulled the bulb out and more of the ceramic fell away. The last time I was able to push it in all the way and the terminal on the wire did not push out the rear of the connector.The light is functional, but I know the next time I need to replace a bulb, I will have to replace the harness too. Plain and simple, these are junk and good for only one use. I would NOT buy again.

I was having problems with the heat created from high wattage bulbs melt the plastic making a loose connection. With ceramic the melting problem ended. Always check for a poor ground or wiring that’s too light for the demand first because this will create the same Melting problem. Often if you take the time to find the source of the problem the fix is quick and easy.

Item as described. No complaints.

My headlight connector had melted on one of the headlights on my 2014 Kia Forte. I got on Amazon and ordered the top rated iJDMTOY connectors and installed it with a new headlight bulb thinking my problem was fixed. A couple weeks later I start getting intermittent headlight outage on that headlight and I write it off as a loose connection on my part since it was under 20 degrees outside ,windy, and dark when I installed it. When I went to check it out on a nice warmer day, I found that the new connector had melted and I had actually done a good job. So this time I ordered the GZXY hi temperature ceramic connectors. When they came in I could see immediately that they were superior to my first purchase. Not only the ceramic connectors, but the wire is a much heavier gauge. The heavier gauge wire I believe is the key along with better connectors. Since I installed this, I have had no further problems with connectors melting. I highly recommend this product. I have pictures included with the iJDMTOY on the left and the GZXY on the right. Also a picture of the melted iJDMTOY.

It is working well as intended. If you're tired to change light bulbs every so often because the car manufacturer was too cheap to use ceramic for the wire socket instead of plastic, then you have a long-term fix with this!

Nice product

Worked wellBut broke one pushing it in due to a smallAmount of melted material fromPrevious connectorMake sure everything is perfect first

Product was deformed and of dubious quality.